Optimal control of induction heating in the surfacing processes of thin shaped disks

Article Sidebar

Published: 28-04-2020
DOI: https://doi.org/10.33108/visnyk_tntu2020.01.005
Keywords:
induction heating, surfacing, optimal law, capacity, temperature, thin shaped disks

Main Article Content

Volodymyr Havryliuk
Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine
Volodymyr Mykhailyshyn
Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine
Mykhailo Mykhailyshyn
Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine
Cheslav Pulka
Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine

Abstract

Induction heating is used by technological processes of surfacing. The advantages of induction heating are high concentration of energy at the heating area that allows to increase the productivity of process, because time of surfacing decreases. The disadvantages of induction heating are electromagnetic radiation and excessive loss of electrical energy. The authors deal with development of the optimal law for source capacity change by using methods of calculation. It allows to reduce electrical energy consumption by 36,8% and 15,8% compared with traditional laws of capacity distribution.

Article Details

Issue

Vol. 97 No. 1 (2020)

Section

Articles
Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

References

1. Sluhockiy A. E. Induktory dlya idukcionnogo nagreva. Leningrad: Energiya, 1974. 264 p. [In Russian].

2. Podstryhach Ya. S., Shvets’ R. N. Termoupruhost’ tonkih obolochek. Kiev: Naukova dumka, 1978. 343 p. [Іn Russian].

3. Podstryhach Ya. S., Koliano Yu. M., Semerak M. M. Temperaturnye polia i napriagenia v elektro- vakuumnyh priborah. Kiev: Naukova dumka, 1981. 342 p. [Іn Russian].

4. Shabliy O. M., Pulka Ch. V., Senchushyn V. S., Havryliuk V. Ya. Rozroblennya energooshchadnyh nahrivalnyh system dlya indukciynoho naplavlennya detalei sil’s’kogospodarskyh mashyn. Visnyk TNTU. No. 4. 2011. Р. 107–120. [In Ukrainian].

5. Shabliy O. M., Pulka Ch. V., Havryliuk V. Ya., Senchushyn V. S. Regymy indukciynogo naplavlennya detaley z urahuvannyam vykorystannya teplovyh I electromagnitnyh poliv. Visnyk TNTU. Vol. 73. No. 1.2014. Р. 109–118. [In Ukrainian].

6. Ryabcev I. A. Naplavka detalei mashyn i mehanizmov. Kiev: Ecotehnologia, 2004. 160 p. [Іn Russian].

7. Tkachev V. N. Iznos i povyshenie dolgovechnosti detaley selskohoziaestvennyh mashyn. Moskva: Mashynostroenie, 1971. 264 p. [Іn Russian].

8. Shabliy O. N., Pulka Ch. V., Budzan B. P. Optimizacyia energozatrat pri indukcyonnoy naplavke tonkostennyh diskov. Avtomaticheskaya svarka. Vol. 487. No. 1. 1987. Р. 36–39. [Іn Russian].

9. Shabliy O. N., Pulka Ch. V., Budzan B. P. Puti ekonomii elektroenergii pri indukcyonnoy naplavke tonkostennyh diskov. Avtomaticheskaya svarka. Vol. 429. No. 12. 1988. Р. 56–58. [Іn Russian].