Defining parameters of elastic-safety clutches for screw conveyers https://doi.org/10.33108/visnyk_tntu2017.03.072
Article Sidebar
Main Article Content
Abstract
The designs of elastic-safety clutches of screw conveyors are offered allowing, except safety conditions, due to damping and elastic properties to ensure smooth start of conveyor screw while in drive run-up and reduce the sharpness of changes in load on it during operation and overloading. The analytical dependence
of the determination of impact loads with axial and torque shocks in the investigated clutch at the boundary moment of its actuation is given. The graphical dependences of the change in the torque value depending on the movement of the movable half-clutch in the mode of protection device actuation at different angle of the hitch inclination are shown.
Article Details
Issue
Section
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
1. Zenkov, R.L. Mashiny nepreryvnoho transporta [Text], R.L. Zenkov, I.I. Ivashkov, L.M. Kolobov, M., Mashinostroenie, 1987. − 320 p.
2. Hrihorev, A.M. Vintovye konveery [Text], A.M. Hrihorev. − M. Mashinostroenie, 1972, 184 p.
3. Hevko, B.M. Mekhanizmy z hvyntovymy prystroiamy [Text], B.M. Hevko, M.H. Danylchenko, R.M. Rohatynskyi and other − Lviv: Svit, 1993. − 208 p.
4. Rohatynskyi, R.M. Naukovi prykladni osnovy stvorennia hvyntovykh transportno-tekhnolohichnykh mekhanizmiv [Text], R.M. Rohatynskyi, I.B. Hevko, A.Ye. Diachun, Ternopil, 2014, 280 p.
5. Rohatynskyi, R.M., Hevko I.B. Model konstruiuvannia i vyboru hvyntovykh konveieriv z rozshyrenymy tekhnolohichnymy mozhlyvostiamy [Text], R.M. Rohatynskyi, I.B. Hevko. Visnyk TNTU, Ternopil, 2012, No 3 (67), P. 197 – 210.
6. Holubentsev, A.N. Dinamika perekhodnykh protsessov v mashinakh so mnohimi massami [Text], A.N. Holubentsev, M., MAShHIZ, 1959, 180 p.
7. Komarov, M.S. Dinamika mashin [Text], M.S. Komarov, M., Mashinostroenie, 1979, 342 p.
8. Loveykin V., Javorska A. Screw feeder: optimization of motion modes considering that the moments of resistance forces change under linear law. MOTROL. Commission of Motorization and Energetics in Agriculture, 2012. Vol. 14, no. 3, pp. 40 – 46.
9. Poliakov, V.S. Spravochnik po muftam [Text], I.D. Barabash, O.A. Rekhovskii, Mashinostroenie, 1974, 352 p.
10. Tepinkichiev, V.K. Predokhranitelnye ustroistva ot perehrevki stankov [Text], V.K. Tepinkichiev, M. Mashinostroenie, 1964, 157 p.
11. Malashchenko, V.O. Mufty pryvodiv. Konstruktsii ta pryklady rozrakhunkiv [Text], V.O. Malashchenko, Lviv: vyd-vo Nats. un-tu "Lvivska politekhnika", 2006, 196 p.
12. Nahorniak, S.H. Predokhranitelnye mekhanizmy metaloobrabatyvaiushcheho oborudovaniia: Spravochnik [Text], S.H. Nahorniak, I.V. Lutsiv, Kiev: Tekhnika, 1992, 72 s