Calculation of constructive parameters of SMA damper https://doi.org/10.33108/visnyk_tntu2017.04.007
Article Sidebar
Main Article Content
Abstract
Shape memory alloy (SMA) based damper device is presented in this paper. The device is composed of pre-tensioned SMA wires and two pre-compressed springs which supply tension of the wires. Pre-tensioned SMA wires provide the system reliability and good damping properties. After removing the external load
pre-compressed springs provide recovery of the device to its original shape. The calculation method of strength and constructive parameters of the damping device is offered. The internal force, the maximal displacement value and the pre-tension magnitude of SMA wires are defined. The maximum allowable internal force of the wires is determined.
Article Details
Issue
Section
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
1. Giurgiutiu V., Zagrai A. The Use of Smart Materials Technologies in Radiation Environment and Nuclear Industry ,, Proceedings of SPIE. 2000. P. paper # 3985.103.
2. Bucht A. et al. Industrial Applications of Shape Memory Alloys Potentials and Limitations ,, Innovative Small Drives and Micro-Motor Systems; 9. GMM,ETG Symposium. 2013. P. 1 – 6.
3. Mohd Jani J. et al. A review of shape memory alloy research, applications and opportunities ,, Mater. Des. Elsevier, 2014. Vol. 56. P. 1078 - 1113.
https://doi.org/10.1016/j.matdes.2013.11.084
4. Hartl D.J. et al. Standardization of shape memory alloy test methods toward certification of aerospace applications, Smart Mater. Struct. 2015. Vol. 24, No 8. P. 82001.
5. Pittaccio S. et al. Applications of Shape Memory Alloys for Neurology and Neuromuscular Rehabilitation ,, J. Funct. Biomater., ed. Petrini L. MDPI, 2015. Vol. 6, No 2. P. 328 – 344.
6. Karthik G., Kashyap B., Prabhu T.R. Processing, properties and applications of Ni-Ti-Fe shape memory alloys,, Mater. Today Proc. Elsevier, 2017. Vol. 4, No 2. P. 3581 - 3589.
https://doi.org/10.1016/j.matpr.2017.02.250
7. Iasnii V. P., Dyvdyk O. V., Lysenko Ya. R. (2017) Modeliuvannia MSE mekhanichnoi povedinky splaviv z pamiattiu formy. Proceedings of the Conference „In-service damage of materials, its diagnostics and prediction“ (Tern., 19 – 22 September 2017), pp. 60 – 62 [in Ukrainian].
8. Oshida Y. et al. Biological and Chemical Evaluation of TiNi Alloys ,,Martensitic Transformations. Trans Tech Publications, 1991. Vol. 56. P. 705 – 710.
9. Lekston Z., Drugacz J., Morawiec H. Application of superelastic NiTi wires for mandibular distraction,Mater. Sci. Eng. A. Elsevier, 2004. Vol. 378, No 1-2. P. 537 - 541.
https://doi.org/10.1016/j.msea.2003.12.061
10.Rondelli G. Corrosion resistance tests on NiTi shape memory alloy,, Biomaterials. 1996. Vol. 17. P. 2003-2008.
https://doi.org/10.1016/0142-9612(95)00352-5
11. K. O., C.M. W. Shape Memory Materials. Cambridge, Mass, USA: Cambridge University Press, 1998. 300 p.
12. Wolons D., Gandhi F., Malovrh B. Experimental Investigation of the Pseudoelastic Hysteresis Damping Characteristics of Shape Memory Alloy Wires,, J. Intell. Mater. Syst. Struct. 1998. Vol. 9, No 2. P. 116-126.
https://doi.org/10.1177/1045389X9800900205
13. Ma H., Wilkinson T., Cho C. Feasibility study on a self-centering beam-to-column connection by using the superelastic behavior of SMAs,, Smart Mater. Struct. 2007. Vol. 16, No 5. P. 1555 - 1563.
https://doi.org/10.1088/0964-1726/16/5/008
14.Isalgue A. et al. SMA for Dampers in Civil Engineering,, Mater. Trans. 2006. Vol. 47, No 3. P. 682 - 690.
https://doi.org/10.2320/matertrans.47.682
15. Ma H., Yam M.C.H. Modelling of a self-centring damper and its application in structural control,, J. Constr. Steel Res. Elsevier, 2011. Vol. 67, No 4. P. 656 - 666.
https://doi.org/10.1016/j.jcsr.2010.11.014
16. Torra V. et al. The SMA: An Effective Damper in Civil Engineering that Smoothes Oscillations ,, Mater. Sci. Forum. Trans Tech Publications, 2012. Vol. 706 – 709. P. 2020 – 2025.
17.Iasnii P., Yasnii V. Dempfuiuchyi prystrii dlia transportuvannia dovhomirnykh konstruktsii: pat. 116582 Ukraina MPK F16F 7/12; opubl. 25.05.2017, Biul. # 10. 2017.